Release 14.7 Map P.20131013 (nt64) Xilinx Mapping Report File for Design 'full_adder' Design Information ------------------ Command Line : map -intstyle ise -p xc6slx45-csg324-3 -w -logic_opt off -ol high -t 1 -xt 0 -register_duplication off -r 4 -global_opt off -mt off -ir off -pr off -lc off -power off -o full_adder_map.ncd full_adder.ngd full_adder.pcf Target Device : xc6slx45 Target Package : csg324 Target Speed : -3 Mapper Version : spartan6 -- $Revision: 1.55 $ Mapped Date : Thu Apr 14 19:58:48 2016 Design Summary -------------- Number of errors: 0 Number of warnings: 0 Slice Logic Utilization: Number of Slice Registers: 0 out of 54,576 0% Number of Slice LUTs: 1 out of 27,288 1% Number used as logic: 1 out of 27,288 1% Number using O6 output only: 0 Number using O5 output only: 0 Number using O5 and O6: 1 Number used as ROM: 0 Number used as Memory: 0 out of 6,408 0% Slice Logic Distribution: Number of occupied Slices: 1 out of 6,822 1% Number of MUXCYs used: 0 out of 13,644 0% Number of LUT Flip Flop pairs used: 1 Number with an unused Flip Flop: 1 out of 1 100% Number with an unused LUT: 0 out of 1 0% Number of fully used LUT-FF pairs: 0 out of 1 0% Number of slice register sites lost to control set restrictions: 0 out of 54,576 0% A LUT Flip Flop pair for this architecture represents one LUT paired with one Flip Flop within a slice. A control set is a unique combination of clock, reset, set, and enable signals for a registered element. The Slice Logic Distribution report is not meaningful if the design is over-mapped for a non-slice resource or if Placement fails. IO Utilization: Number of bonded IOBs: 5 out of 218 2% Number of LOCed IOBs: 5 out of 5 100% Specific Feature Utilization: Number of RAMB16BWERs: 0 out of 116 0% Number of RAMB8BWERs: 0 out of 232 0% Number of BUFIO2/BUFIO2_2CLKs: 0 out of 32 0% Number of BUFIO2FB/BUFIO2FB_2CLKs: 0 out of 32 0% Number of BUFG/BUFGMUXs: 0 out of 16 0% Number of DCM/DCM_CLKGENs: 0 out of 8 0% Number of ILOGIC2/ISERDES2s: 0 out of 376 0% Number of IODELAY2/IODRP2/IODRP2_MCBs: 0 out of 376 0% Number of OLOGIC2/OSERDES2s: 0 out of 376 0% Number of BSCANs: 0 out of 4 0% Number of BUFHs: 0 out of 256 0% Number of BUFPLLs: 0 out of 8 0% Number of BUFPLL_MCBs: 0 out of 4 0% Number of DSP48A1s: 0 out of 58 0% Number of ICAPs: 0 out of 1 0% Number of MCBs: 0 out of 2 0% Number of PCILOGICSEs: 0 out of 2 0% Number of PLL_ADVs: 0 out of 4 0% Number of PMVs: 0 out of 1 0% Number of STARTUPs: 0 out of 1 0% Number of SUSPEND_SYNCs: 0 out of 1 0% Average Fanout of Non-Clock Nets: 1.00 Peak Memory Usage: 482 MB Total REAL time to MAP completion: 5 secs Total CPU time to MAP completion: 4 secs Table of Contents ----------------- Section 1 - Errors Section 2 - Warnings Section 3 - Informational Section 4 - Removed Logic Summary Section 5 - Removed Logic Section 6 - IOB Properties Section 7 - RPMs Section 8 - Guide Report Section 9 - Area Group and Partition Summary Section 10 - Timing Report Section 11 - Configuration String Information Section 12 - Control Set Information Section 13 - Utilization by Hierarchy Section 1 - Errors ------------------ Section 2 - Warnings -------------------- Section 3 - Informational ------------------------- INFO:MapLib:562 - No environment variables are currently set. INFO:LIT:244 - All of the single ended outputs in this design are using slew rate limited output drivers. The delay on speed critical single ended outputs can be dramatically reduced by designating them as fast outputs. INFO:Pack:1716 - Initializing temperature to 85.000 Celsius. (default - Range: 0.000 to 85.000 Celsius) INFO:Pack:1720 - Initializing voltage to 1.140 Volts. (default - Range: 1.140 to 1.260 Volts) INFO:Map:215 - The Interim Design Summary has been generated in the MAP Report (.mrp). INFO:Pack:1650 - Map created a placed design. Section 4 - Removed Logic Summary --------------------------------- Section 5 - Removed Logic ------------------------- Section 6 - IOB Properties -------------------------- +---------------------------------------------------------------------------------------------------------------------------------------------------------+ | IOB Name | Type | Direction | IO Standard | Diff | Drive | Slew | Reg (s) | Resistor | IOB | | | | | | Term | Strength | Rate | | | Delay | +---------------------------------------------------------------------------------------------------------------------------------------------------------+ | a | IOB | INPUT | LVCMOS25 | | | | | | | | b | IOB | INPUT | LVCMOS25 | | | | | | | | cin | IOB | INPUT | LVCMOS25 | | | | | | | | cout | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | | | s | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | | +---------------------------------------------------------------------------------------------------------------------------------------------------------+ Section 7 - RPMs ---------------- Section 8 - Guide Report ------------------------ Guide not run on this design. Section 9 - Area Group and Partition Summary -------------------------------------------- Partition Implementation Status ------------------------------- No Partitions were found in this design. ------------------------------- Area Group Information ---------------------- No area groups were found in this design. ---------------------- Section 10 - Timing Report -------------------------- A logic-level (pre-route) timing report can be generated by using Xilinx static timing analysis tools, Timing Analyzer (GUI) or TRCE (command line), with the mapped NCD and PCF files. Please note that this timing report will be generated using estimated delay information. For accurate numbers, please generate a timing report with the post Place and Route NCD file. For more information about the Timing Analyzer, consult the Xilinx Timing Analyzer Reference Manual; for more information about TRCE, consult the Xilinx Command Line Tools User Guide "TRACE" chapter. Section 11 - Configuration String Details ----------------------------------------- Use the "-detail" map option to print out Configuration Strings Section 12 - Control Set Information ------------------------------------ Use the "-detail" map option to print out Control Set Information. Section 13 - Utilization by Hierarchy ------------------------------------- Use the "-detail" map option to print out the Utilization by Hierarchy section.